3. Create Program to control LED from labview interface with Arduino

Create Program to control LED from labview interface with Arduino

Watch video:

Like share comment and subscribe....

Thank you.....

2. Led control using Labview interface with Arduino using LINX

Learn to Led control using Labview interface with Arduino using LINX

Watch video:

Like comment share and subscribe......

Thank you.....

1. First step to interface Arduino with Labview

Hi in this article Learn how to interface and program arduino with labview..

Watch video:

Thankyou.... 

Like comment share subscribe....

6. Learn how to use comparators and indicators(LED) in labview

Hi in this article Learn how to use comparators and indicators(LED) in labview program..

Procedure:

Step 1:  Open labview software..

Step 2:  Open blank VI..

Step 3: Use block diagram panel to program

Step 4:  Use Right click to get codes

Step 5: Follow Right click-Numeric-Add

Step 6:  Place the Addition tool where we want

Step 7:  Then Right click at node of input to addition tool

Step 8: Create Control and enter input

Step 9: Now create indicator by using right click at the output node at addition pin

Step 10: Now we are going to use comparison command to use comparison between the two
               Numbers in the function

Step 11: 1st use Greater than command from command bar

Step 12: Next select Less command from command bar...

Step 14: connect each comparison command 1st input with addition out put to compare...

Step 15: Create constant input like (10) for other input in comparators..

Step 16: Use indicator on both comparators...

Step 17: That indicator is like led...

Step 18: Run the program continuously...

Step 19: So program obey the condition

Step 20: Check weather the program is correct or wrong

Step 21: Run continuously if program is correct otherwise check the program

Step 22: Use Front panel to RUN...

Step 23: Enter inputs in the front panel

Step 24:  Now get the results...

Watch video:

Thank you.....

5. Addition of 2 number and implimenting comparators and indicators using Labview

Hi in this article learn how to add two numerical
numbers using labview coding...

Procedure:

Step 1:  Open labview software..

Step 2:  Open blank VI..

Step 3: Use block diagram panel to program

Step 4:  Use Right click to get codes

Step 5: Follow Right click-Numeric-Add

Step 6:  Place the Addition tool where we want

Step 7:  Then Right click at node of input to addition tool

Step 8: Create Control and enter input

Step 9: Now create indicator by using right click at the output node at addition pin

Step 10: Now we are going to use comparison command to use comparison between the two
               Numbers in the function

Step 11: 1st use Greater than command from command bar

Step 12: Next select Less command from command bar...

Step 14: connect each comparison command 1st input with addition out put to compare...

Step 15: Create constant input like (10) for other input in comparators..

Step 16: Use indicator on both comparators...

Step 17: That indicator is like led...

Step 18: Run the program continuously...

Step 19: So program obey the condition

Step 20: Check weather the program is correct or wrong

Step 21: Run continuously if program is correct otherwise check the program

Step 22: Use Front panel to RUN...

Step 23: Enter inputs in the front panel

Step 24:  Now get the results...

Watch video:

  

Thank you.....

4. Division of two numbers using Labview

Hi in this article learn how to division of two numerical
numbers using labview coding...

Procedure:

Step 1:  Open labview software..

Step 2:  Open blank VI..

Step 3: Use block diagram panel to program

Step 4:  Use Right click to get codes

Step 5: Follow Right click-Numeric-division

Step 6:  Place the division tool where we want

Step 7:  Then Right click at node of input to division tool

Step 8: Create Control at enter input

Step 9: Now create indicator by using right click at the output node at division pin

Step 10: Check weather the program is correct or wrong

Step 11: Run continuously if program is correct otherwise check the program

Step 12: Use Front panel to RUN...

Step 13: Enter inputs in the front panel

Step 14:  Now get the results...

Watch video:

3. Multiplication of two numbers using Labview

Hi in this article learn how to Multiplication two numerical
numbers using labview coding...

Procedure:

Step 1:  Open labview software..

Step 2:  Open blank VI..

Step 3: Use block diagram panel to program

Step 4:  Use Right click to get codes

Step 5: Follow Right click-Numeric-Multiply

Step 6:  Place the Multiply tool where we want

Step 7:  Then Right click at node of input to Multiplication tool

Step 8: Create Control at enter input

Step 9: Now create indicator by using right click at the output node at multiplication pin

Step 10: Check weather the program is correct or wrong

Step 11: Run continuously if program is correct otherwise check the program

Step 12: Use Front panel to RUN...

Step 13: Enter inputs in the front panel

Step 14:  Now get the results...

Watch video:

2. Subtraction of two numbers using Labview

Hi in this article learn how to Sub two numerical
numbers using labview coding...

Procedure:

Step 1:  Open labview software..

Step 2:  Open blank VI..

Step 3: Use block diagram panel to program

Step 4:  Use Right click to get codes

Step 5: Follow Right click-Numeric-Sub

Step 6:  Place the Subtraction tool where we want

Step 7:  Then Right click at node of input to subtraction tool

Step 8: Create Control at enter input

Step 9: Now create indicator by using right click at the output node at Subtraction pin

Step 10: Check weather the program is correct or wrong

Step 11: Run continuously if program is correct otherwise check the program

Step 12: Use Front panel to RUN...

Step 13: Enter inputs in the front panel

Step 14:  Now get the results...

Watch video:

1. Addition of 2 number using Labview

Hi in this article learn how to add two numerical
numbers using labview coding...

Procedure:

Step 1:  Open labview software..

Step 2:  Open blank VI..

Step 3: Use block diagram panel to program

Step 4:  Use Right click to get codes

Step 5: Follow Right click-Numeric-Add

Step 6:  Place the Addition tool where we want

Step 7:  Then Right click at node of input to addition tool

Step 8: Create Control at enter input

Step 9: Now create indicator by using right click at the output node at addition pin

Step 10: Check weather the program is correct or wrong

Step 11: Run continuesly if program is correct otherwise check the program

Step 12: Use Front panel to RUN...

Step 13: Enter inputs in the front panel

Step 14:  Now get the results...

Watch video: